You are here

Jonny Harianto

  • Associate Director, Gear Lab, Mechanical & Aerospace Engr
  • 201 W 19th Ave
    E313
    Columbus, OH 43210
  • 614-688-3952

About

Research Interests and Responsibilities

Gear analysis and design, transmission errors, gear and spline load distribution, gear robustness and optimization.  I am responsible on many of GearLab software and GearLab administrative.  Liaison to GearLab consortium members.

Degrees

  • 1995 - M.Sc. in Mechanical Engineering, The Ohio State University
    Thesis: "The Effect of Manufacturing Errors on Predicted Dynamic Factors of Spur Gears"
  • 1993 - B.Sc. in Mechanical Engineering (with Honors Research Distinction), The Ohio State University
    Thesis: "Performance Evaluation of Passive and Electronically Controlled Pneumatic Suspension using a Quarter Car Model"

Honors & Awards

  • 1995 - Dorothy Brickman Leadership Award - The Ohio State University
  • 1994 - Excellent Service Award, Indonesian Student Association
  • 1989 - 1993 :
    • Tau-Beta-Pi, The National Dean’s Lists, Phi-Kappa-Phi, Phi-Eta-Sigma
    • Automotive Engineering Research Scholarship, Fluid Power Foundation Scholarship, John & Mildred Lumley Engineering Scholarship, TREP Scholarship, and Roberta B. Nicholson Scholarship

Hobbies

Traveling, photography, couponing, and frequent flyer enthusiastic.

Publications

  • Artoni, A., Guiggiani, M., Kahraman, A., and Harianto, J., “Robust Optimization of Helical Gear Surface Modifications within Ranges of Torque and Misalignments,” ASME Power Transmission and Gearing Conference, Portland, OR, August 2013.
  • Sanders, A., Houser, D.R., Kahraman, A., Harianto, J., and Shon, S., “An Experimental Investigation of the Effect of Tooth Asymmetry and Tooth Root Shape on Root Stresses and Single Tooth Bending Fatigue Life of Gear Teeth,” ASME Power Transmission and Gearing Conference, Washington D.C., August 2011.
  • Li, S., Vaidyanathan, A., Harianto, J., and Kahraman, A., “Influence of Design Parameters and Micro-Geometry on Mechanical Power Losses of Helical Gear Pairs,”  JSME International Conference - Motion and Power Transmission, Sendai, Japan, May 2009.
  • Harianto, J. and Houser, D.R., “A Methodology for Obtaining Optimum Gear Tooth Micro-Topographies for Noise and Stress Minimization over a Broad Operating Torque Range,” ASME Power Transmission and Gearing Conference, Las Vegas, NV, September 2007.
  • Houser, D.R., Shon, S., and Harianto, J., “An Evaluation of FZG Micro-Pitting Test Procedures and Results for the Crowned AGMA Test Gears,” AGMA Fall Technical Meeting, Orlando, FL, 2006.
  • Harianto, J., and Houser, D. R., “The Effect of Micro-Geometry and Load on Helical Gear Noise Excitations,” SAE Noise and Vibration Conference, Traverse City, MI, 2005.
  • Harianto, J., and Houser, D.R., “The Effect of Profile Relief on the Noise Excitation of Helical Gear,” Gear Solutions Magazine, March 2005.
  • Chang, S., Houser, D.R., and Harianto, J., “Tooth Flank Corrections of Wide Face Width Helical Gears That Account for Shaft Deflections,” ASME Power Transmission and Gearing Conference, Chicago, IL, 2003.
  • Houser, D.R., Sorenson, J., Harianto, J., Wijaya, H., and Satyanarayanan, M., “Comparison of Analytical Predictions with Dynamic Noise and Vibration Measurements for a Simple Idler Gearbox,” ASME Power Transmission and Gearing Conference, 2002.
  • Harianto, J., and Houser, D.R., “A Gear Design Optimization Procedure that Identifies Robust, Minimum Stress and Minimum Noise Gear Pair Designs,” AGMA Fall Technical Meeting, St. Louis, MO, October 2002.
  • Harianto, J., and Houser, D.R., “Manufacturing Robustness Analysis of the Noise Excitation and Design of Alternative Gear Sets,” SAE Noise and Vibration Conference, 2001.
  • Harianto, J., and Houser, D.R., “Design Robustness and Its Effect on Transmission Error and Other Design Parameters,” International Conference on Mechanical Transmissions, China, 2001.
  • Houser, D., Wijaya H., and Harianto, J., “The Effect of Spacing Errors and Runout on Transverse Load Sharing and Dynamic Factor of Spur and Helical Gears,” AGMA Fall Technical Meeting, Detroit, MI, October 3-5 2001.
  • Houser, D. R., Sorenson, J., and Harianto, J., “Development of a Data Base for Transmission Noise Evaluation,”  The India-USA Symposium on Emerging Trends in Vibration and Noise Engineering, Columbus, OH, December 2001.
  • Ueda, Y., Houser, D.R., and Harianto, J., “The Effect of Manufacturing Errors on Gear Design Metrics using a Robustness Scheme,” JSME International Conference - Motion and Power Transmission, Fukuoka, Japan, November 2001.
  • Houser, D. R., Harianto, J., Chandrasekaran, B., Josephson, J. R., and Iyer, N., “A Multi-Variable Approach to Determine the "Best" Gear Design,” ASME Power Transmission and Gearing Conference, Baltimore, MD, September 2000.
  • Houser, D.R., Lim, T. C., Harianto, J., Sorenson, J. D., Myers, C. H., and Gordon, B.E., “Case History: Engine Timing Gear Noise Reduction,” SAE Noise and Vibration Conference, 1999.
  • Harianto, J., and Houser, D.R., “A Method for Predicting the Dynamic Root Stresses of Helical Gear Teeth,” AGMA Fall Technical Meeting, 1998.
  • Harianto, J., and Houser, D.R., “The Effect of Manufacturing Errors on the Predicted Dynamic Factors of Spur Gears,” AGMA Fall Technical Meeting, Alexandria, USA, 1995.